Compulsory concrete mixer repair and watch the legend

Our company can supply all of our product information, for planning and design, installation, configuration, operation, and maintenance. To provide users with the whole picture of the product solidarity. Compulsory concrete mixer equipment in the professional production of the time, because of its greater intensity of production, it is difficult enough to be some unexpected blow, the result today, let Yu Shan notice you. YHZS25 Mobile Concrete Mixing Plant From China Manufacturer 1. Adjust the roller bracket (or rack) method: If the total deviation to the side of the tape at no load, you should run the laterality of the roller bracket advancing along the tape running direction 1-2cm, or to another side roller brackets (or chassis) as appropriate heightening. 2. Check the air compressor to protect themselves before checking device is reliable, the pressure is stable; check the electrical device is safe and reliable operation of the limit switch each switch is flexible and reliable; check Mixer blade coupling bolts are secure; check water pump Whether to add a little pipe is smooth; Doumen silo, cement and other closing Doumen is flexible and reliable; check the gear box lubrication point anxious whether there is enough oil. 3. Construction of concrete assignments and schedule; by this two parameter to choose how much of specifications compulsory concrete mixer. The total amount set concrete tasks for the M; the number of days pouring concrete for the T; the number of working hours per day are H; utilization factor of K, should be used compulsory concrete mixer specifications X = M / (T * H * K), where K is 0.7-0.9. It should also be considered in the selection of the transport situation in the finished concrete. Such as: direct pumping or transport vehicle. Volume delivery vehicle is an important basis for decision forced concrete mixer models. 4. Ban the driver shall absent without leave, should always observed anomaly or abnormal sound, should be compulsory concrete mixer garland memory was discharged after a power failure shut down wind up to be checked repairs

Concrete mixing station equipment which must be concerned about the use of security issues

 Use concrete mixing station equipment which must focus on security issues? Concrete mixing station grinder operator should be carefully, seriously in the production of security issues. In addition to the factory must strictly observe all small concrete batch plant Suppliers safety regulations and workshop, the combination of the working characteristics of mill workers, but also must do the following: Before work, carefully inspect the wheel for cracks, whether there were unusual sound when tapped with a wooden pine fixed wheel nuts are tightened. After identify no such problems, after two minutes idle test, in order to start work.

      

Concrete mixing station grinder operator should be carefully, seriously in the production of security issues. In addition to the need to strictly abide by the factories and workshops of the safety regulations, combined with mill workers work characteristics, but also you must do the following:

      

  • 1) Before work, carefully check the wheel for cracks, for unusual sounds when tapping pine wood, whether fixed wheel nut tightened. After identify no such problems, after two minutes idle test, in order to start work.
  •       
  • 2) grinding concrete mixing plant parts, you must start at the wheel and the workpiece before eating knife, and then stop at the wheel retraction, or easily crushed wheel and damage to the machine, resulting in serious accidents.
  •       
  • 3) grinding concrete mixing knife can not eat too much when you stop the workpiece to prevent the workpiece burn, wheel rupture, causing serious accidents.
  •       
  • 4) a concrete mixing station workpiece is completed, the wheel must feed handwheel quit a storm, so installed again when the next workpiece driving wheel collision still work: At the end of a paragraph or complete the work, about the manipulation of the handle should be dense bed it in the "neutral" position to avoid sudden movement when then drive components and accidents.
  •       
  • 5) In addition to the replacement small concrete batch plant manufacturers wheel should be carefully examined, but also the need for wheel balance again.
  •       
  • 7) using a magnetic chuck, magnetic chuck must carefully check the reliability of the workpiece can not drive a car when suction is not in prison, to prevent injury or damage the workpiece flying machine equipment.
  •       
  • 8) The change must be carefully adjusted to the stopper position given push to drive after tightening. To prevent the stopper leaving table travel too far to walk, so the wheel against a concrete mixing station all parts of the machine and cause an accident.